graph
- (issue1753) Implement PDF export of SQ Measurement data.2015-03-16, by Andre Heinecke
- (issue1753) Use different theme for measurements overview and single diagrams2015-03-16, by Andre Heinecke
- Renable access to seddb sessions2015-03-11, by Andre Heinecke
- Merge of MINFO improvement developments2015-03-10, by Andre Heinecke
- There seems to be no use case for not overriding these methods.2015-03-06, by Tom Gottfried
- The bug that motivated this extremely defensive error-handling was fixed in Rev fe7e9da6312a by nomore calling close() on a private variable.2015-03-06, by Tom Gottfried
- Remove superfluous private variable.2015-03-06, by Tom Gottfried
- (issue1798) Adjust WinCM according to W in NHN axis on explicit zoom2015-02-27, by Andre Heinecke
- Do not get any wst values just to get the name of the differences for export.2015-02-26, by Andre Heinecke
- Readd StaticWQKmsCacheKey and use it again.2015-02-26, by Andre Heinecke
- Use updated class name instead of no more existant.2015-02-26, by Tom Gottfried
- (issue1797) Increase session debug output2015-02-24, by Andre Heinecke
- (issue1797) Move close into session release and guard it.2015-02-24, by Andre Heinecke
- Replace offensive comment by a more constructive note.2015-02-17, by Andre Heinecke
- (Issue1755) Add distance step selection to bed quality artifact2015-02-16, by Andre Heinecke
- Move static operation out of loop.2015-02-16, by Andre Heinecke
- (issue1755) Move KM Step handling from Winfo artifact to RangeAccess2015-02-16, by Andre Heinecke
- Accept more elevation system names (e.g. with hyphen).2015-02-16, by Tom Gottfried
- Meta-data on sounding width associated to bed heights is redundant to real data associated to values.2015-02-16, by Tom Gottfried
- Bed heights are just bed heights since a while ('single' is obsolete).2015-02-16, by Tom Gottfried
- Remove obsolete class hierarchy for bed height data.2015-02-16, by Tom Gottfried
- Abstract parser for bed heights is obsolete.2015-02-16, by Tom Gottfried
- Importer: Remove obsolete interface for bed heights.2015-02-16, by Tom Gottfried
- Remove obsolete interface for bed height values.2015-02-16, by Tom Gottfried
- Morphological width imported and stored with heights is redundant to table morphologic_width.2015-02-16, by Tom Gottfried
- bed height differences datacage: only supply differences where subtrahend is older than minuend or year is unknown.2015-02-16, by Tom Gottfried
- (issue1754) Add km filtering for winfo anf fixanal results in difference calculations2015-02-16, by Andre Heinecke
- Actually configure a bedheight cache.2015-02-16, by Andre Heinecke
- (issue1754) Fix wst static cache name.2015-02-16, by Andre Heinecke
- (issue1754) Extend WKms interface for KM filtering2015-02-16, by Andre Heinecke
- (issue1754) Gracefully handle empty differenc results (e.g from km 0,001 to 0,002)2015-02-16, by Andre Heinecke
- (issue1754) Add distantce handling to WINFO differences state2015-02-16, by Andre Heinecke
- Warn for not implemented difference handling of minfo artifacts.2015-02-16, by Andre Heinecke
- (issue1750) It is an error if there are more then two stations at the same range.2015-02-13, by Andre Heinecke
- (Issue1754) Make BedDifference calculation range dependent.2015-02-13, by Andre Heinecke
- (issue1750) Take Static SQ Relations based on a range and merge them together2015-02-13, by Andre Heinecke
- (issue1753) Remove "measured" from CSV header2015-02-13, by Andre Heinecke
- (issue1753) Add measurements to CSV export2015-02-13, by Andre Heinecke
- (issue1753) Add SQ Measurement dates as text annotations to points2015-02-13, by Andre Heinecke
- (issue1753) Carry measurement date through SQ values2015-02-13, by Andre Heinecke
- (issue1753) Add label theme for SQMeasurements2015-02-13, by Andre Heinecke
- Log the server startup to stdout2015-02-13, by Andre Heinecke
- (issue1599) Add manualpoints theme for MSH2015-02-12, by Andre Heinecke
- (issue1068) Add different theme for SQOutlier curves and increase SQCurve linesize to 22015-02-12, by Andre Heinecke
- (issue1786) Enable manualline facets for cross section charts2015-02-12, by Andre Heinecke
- (issue869) Remove horizontal lines in parameters2015-02-12, by Andre Heinecke
- (issue1051) Use a list of single years in SedimentLoadYear mode2015-02-11, by Andre Heinecke
- (issue1051) Add input support for epochs2015-02-11, by Andre Heinecke
- (issue1788) Do not divide area by two.2015-02-18, by Andre Heinecke
- (issue1717) Use unified description for y-field in editor for manual points in historical discharge time-diagrams.2015-02-18, by Tom Gottfried
- (issue1795) Handle modules configuration for any module2015-02-17, by Andre Heinecke
- (issue1794) Safeguard against layers without extent.2015-02-17, by Andre Heinecke
- Update uuid of "Rhein"2015-01-30, by Andre Heinecke
- (issue1777) Move logging code for existing tickets to the correct location2015-01-16, by Andre Heinecke
- Remove useless i18n that cannot be called from server anyhow.2015-01-12, by Tom Gottfried
- Release script: build binaries for publication when tagging and slightly mavenize the whole process.2014-12-19, by Tom Gottfried
- Useful default for path to DEMs.2014-12-19, by Tom Gottfried
- It's useful to have an uncompressed tar to which more files can be appended.2014-12-19, by Tom Gottfried
- We don't need the base directory in the assembly.2014-12-19, by Tom Gottfried
- Let overview be the first tab in SQ relation output.2014-12-19, by Tom Gottfried