| Mon, 16 Feb 2015 09:21:49 +0100 |
Tom Gottfried |
Remove obsolete interface for bed height values.
|
| Mon, 16 Feb 2015 09:00:08 +0100 |
Tom Gottfried |
Morphological width imported and stored with heights is redundant to table morphologic_width.
|
| Mon, 16 Feb 2015 08:39:06 +0100 |
Tom Gottfried |
bed height differences datacage: only supply differences where subtrahend is older than minuend or year is unknown.
|
| Mon, 16 Feb 2015 15:31:17 +0100 |
Andre Heinecke |
(issue1754) Add km filtering for winfo anf fixanal results in difference calculations
|
| Mon, 16 Feb 2015 15:30:22 +0100 |
Andre Heinecke |
Actually configure a bedheight cache.
|
| Mon, 16 Feb 2015 15:28:51 +0100 |
Andre Heinecke |
(issue1754) Fix wst static cache name.
|
| Mon, 16 Feb 2015 15:28:22 +0100 |
Andre Heinecke |
(issue1754) Extend WKms interface for KM filtering
|
| Mon, 16 Feb 2015 15:27:39 +0100 |
Andre Heinecke |
(issue1754) Gracefully handle empty differenc results (e.g from km 0,001 to 0,002)
|
| Mon, 16 Feb 2015 12:55:38 +0100 |
Andre Heinecke |
(issue1754) Add distantce handling to WINFO differences state
|
| Mon, 16 Feb 2015 11:30:27 +0100 |
Andre Heinecke |
Warn for not implemented difference handling of minfo artifacts.
|
| Fri, 13 Feb 2015 16:36:52 +0100 |
Andre Heinecke |
(issue1750) It is an error if there are more then two stations at the same range.
|
| Fri, 13 Feb 2015 16:17:46 +0100 |
Andre Heinecke |
(Issue1754) Make BedDifference calculation range dependent.
|
| Fri, 13 Feb 2015 14:59:16 +0100 |
Andre Heinecke |
(issue1750) Take Static SQ Relations based on a range and merge them together
|
| Fri, 13 Feb 2015 13:44:52 +0100 |
Andre Heinecke |
(issue1753) Remove "measured" from CSV header
|
| Fri, 13 Feb 2015 12:35:18 +0100 |
Andre Heinecke |
(issue1753) Add measurements to CSV export
|
| Fri, 13 Feb 2015 12:34:38 +0100 |
Andre Heinecke |
(issue1753) Add SQ Measurement dates as text annotations to points
|
| Fri, 13 Feb 2015 12:34:06 +0100 |
Andre Heinecke |
(issue1753) Carry measurement date through SQ values
|
| Fri, 13 Feb 2015 12:31:59 +0100 |
Andre Heinecke |
(issue1753) Add label theme for SQMeasurements
|
| Fri, 13 Feb 2015 11:10:19 +0100 |
Andre Heinecke |
Log the server startup to stdout
|
| Thu, 12 Feb 2015 17:29:33 +0100 |
Andre Heinecke |
(issue1599) Add manualpoints theme for MSH
|
| Thu, 12 Feb 2015 12:18:47 +0100 |
Andre Heinecke |
(issue1068) Add different theme for SQOutlier curves and increase SQCurve linesize to 2
|
| Thu, 12 Feb 2015 11:40:08 +0100 |
Andre Heinecke |
(issue1786) Enable manualline facets for cross section charts
|
| Thu, 12 Feb 2015 11:17:46 +0100 |
Andre Heinecke |
(issue869) Remove horizontal lines in parameters
|
| Wed, 11 Feb 2015 18:00:48 +0100 |
Andre Heinecke |
(issue1051) Use a list of single years in SedimentLoadYear mode
|
